SUN HYDRAULICS
FDBAYCV

$120.60 USD

SUN HYDRAULICS
Material:FDBAYCV
Model:FDBA-YCV
Summary:Cartridge

Quantity in stock: 0

***Disclaimer: The following summary contains information gathered from various sources such as product descriptions, technical specifications and catalogs. While efforts have been made to provide accurate details, inaccuracies may occur. It is advised to verify all information by contacting Sun Hydraulics directly.***
The Sun Hydraulics FDBAYCV (Material Number: FDBAYCV) is a fully adjustable, pressure-compensated flow control valve designed for precise flow regulation in applications with significant pressure fluctuations. This model allows for both meter-in and meter-out applications and features a reverse-flow check valve to provide unrestricted flow from port 2 to port 1. It is infinitely adjustable from nearly closed up to the maximum flow capacity of 6 gpm (23 L/min). The valve's balanced adjustment mechanism ensures easy adjustments even under high pressures, while its sharp-edged orifice design minimizes flow variations due to changes in fluid viscosity. This cartridge is designed to be physically and functionally interchangeable with other 2-port flow control cartridges of the same frame size, although extension dimensions may vary. The product can handle a maximum operating pressure of 5000 psi (350 bar) and features minimal leakage of .1 gpm (0.4 L/min) when fully shut off. It includes an integral high-capacity check valve and is equipped with EPDM seals, making it suitable for systems using phosphate ester fluids; however, exposure to petroleum-based fluids should be avoided as it can damage the seals. The FDBAYCV model fits into a T-13A cavity and belongs to Series 1. It features an adjustment range requiring up to 5.5 counterclockwise turns from fully closed to fully open, with specific torque requirements for installation and adjustment components: a valve hex size of .78 inches (22.2 mm), installation torque between 30\u201335 lbf ft (41\u201347 Nm), an adjustment screw internal hex size of .532 inches (4 mm), locknut hex size of .916 inches (15 mm), and locknut torque between 80\u201390 lbf in (9\u201310 Nm). The model weighs approximately .40 lb (.20 kg) and comes with a Viton seal kit option available under part number 990010006.

Description

Fully adjustable, pressure-compensated flow controls with reverse-flow check provide precise flow regulation for meter-in or meter-out applications where there may be wide pressure fluctuations. They are infinitely adjustable from nearly closed up to the maximum flow. An integral high-capacity check valve provides unrestricted flow from port 2 to port 1.

All 2-port flow control cartridges are physically and functionally interchangeable (i.e. same flow path, same cavity for a given frame size). However, cartridge extension dimensions from the mounting surface may vary.
A balanced adjustment mechanism allows for easy adjustment even at high pressures.
The sharp-edged orifice design minimizes flow variations due to viscosity changes.
Minimum leakage is .1 gpm (0,4 L/min) when the adjustment mechanism is turned to the shut-off position.
Cartridges with EPDM seals are for use in systems with phosphate ester fluids. Exposure to petroleum based fluids, greases and lubricants will damage the seals.

Cavity	T-13A
Series	1
Capacity	6 gpm23 L/min.
Maximum Operating Pressure	5000 psi350 bar
Adjustment - Number of Counterclockwise Turns - Fully Closed to Fully Open	55
Valve Hex Size	7/8 in.22,2 mm
Valve Installation Torque	30 - 35 lbf ft41 - 47 Nm
Adjustment Screw Internal Hex Size	5/32 in.4 mm
Locknut Hex Size	9/16 in.15 mm
Locknut Torque	80 - 90 lbf in.9 - 10 Nm
Model Weight	.40 lb0,20 kg
Seal kit - Cartridge	Viton: 990-010-006

Show FAQ

What happens if I block the bypass port on a priority flow control?	The valve acts as a 2 port restrictive flow control.
How big is a drop of hydraulic oil?	There are exactly 250 Sun drops in a cubic inch or 15 in a cc.
How accurate are Sun's flow controls?	We claim +/- 10%. We set to +/- 5% in production testing to allow for differences in customers' conditions. If you want accuracy, stay in the bottom 2/3rds of the range. Our 12 gpm (45 L/min.) flow controls are quite flat at 9 gpm (34 L/min.) and dead flat below 6 gpm (23 L/min.), until you get to the bottom of the range. Below about .25 gpm (1 L/min.), spool leakage and orifice conditions start to limit accuracy.
I have a heat problem, will Sun's priority flow control help?	I am afraid not. Unless you are overflowing your current valve and correctly size ours, you are not likely to notice any improvement. Priority flow controls are not efficient devices. They are an easy way to get more than 1 source of oil from 1 pump but they can generate a lot of heat. Try to size your actuators so the pressures are similar on both the priority and the bypass circuits. If you can't do that, try to have the lower flow leg be the lower pressure. The pump pressure is determined by whichever leg is higher and if there is flow that is taking a pressure drop that is not doing work it is creating heat.
What happens if I block the control flow (priority) port?	All flow is blocked, hence the term priority. The priority flow has to be satisfied.
What is the compensating pressure of Sun's flow controls?	The spring force in our flow controls equates to about 100 psi (7 bar). This is high enough to give the valves acceptable capacity (not really) and not too high for proper circuit operation. 100 psi (7 bar) is the spring force; at the upper end of the flow control's range, the drop through the valve will be as high as 250 psi (17 bar) before it starts modulating.
What is the pressure drop through a flow control?	In a meter-in flow control circuit if the pump is set at 3000 psi and the load is 2000 psi the drop through the flow control is 1000 psi. In a meter-out circuit with the load at 2000 psi the drop through the flow control is 2000 psi.

SUN HYDRAULICSFDBAYCV

SUN HYDRAULICS
FDBAYCV